双层纸怎么制作，双色纸制作方法

　　怎么制作双层纸，制作双层纸张的方法如下：

　　1、在大约250毫升/1杯水中搅拌30毫升/ 1/8杯的甲基纤维素粉末(MC)。

　　2、充分混合，并让其静置，直到看不到任何粉末团块(必要时再次搅拌)。这通常需要至少4小时。

　　3、把混合物勺入瓶中，然后加入另外250毫升/ 1杯水。盖上瓶盖(要拧紧!)并摇晃混合物。

　　4、让瓶中的混合物静置，直到没有明显的气泡。这通常需要至少12小时。此后，混合物将变清澈，并且比水更粘稠。

　　5、彻底清洁板和画笔，以除去任何您不希望出现在纸张上的灰尘或污垢。

　　6、在板上倒入约60毫升/ 1/4杯的MC溶液。使用画笔将混合物均匀地涂抹在板上，覆盖比您将要使用的纸张更大的区域。如果需要，添加更多的MC溶液。

　　7、将一张纸巾绕在圆筒上，避免出现褶皱。这将是第一张纸，也会比第二张纸湿润。这意味着颜色更有可能从这张纸上渗出，因此如果您使用两种不同颜色的纸张，应该在这里使用较浅的颜色纸张。

　　8、将纸巾展开到板上，使其没有任何褶皱。使用画笔将任何气泡从纸巾底部刷到两侧，让纸巾完全平整。要小心进行此操作，因为湿润的纸巾很容易撕裂 - 宽画笔可以避免在任何一个点施加过大的压力。

　　9、再次将第二张纸巾绕在圆筒上，避免褶皱。

　　10、将第二张纸巾展开到板上，使其与第一张纸巾重叠。应该有足够的液体，使没有干燥区域。如果有干燥区域，请小心地在这些区域刷上少量MC溶液。如前所述，使用画笔将任何气泡从纸巾底部刷到两侧，让纸巾完全平整。

　　11、让纸张完全干燥。这可能需要超过24小时。重要的是不要在纸张湿润时剥离其中的部分，因为即使在干燥时，被剥离的区域也会相对于纸张的其余部分变得拉伸。

　　12、当纸张完全干燥后，小心地将其从板上剥离，并按大小裁剪。

　　以上文章由幻幻想折纸内容翻译而来，可能又翻译错误和不准确得地方，可以看英文原文如下：

　　Method: 1. Stir around 30ml / ⅛ cup of methyl cellulose in about 250ml / 1 cup water.

　　2. Mix thoroughly and leave it to rest until you cannot see any clumps of powder (stirring again if necessary). This usually takes at least 4 hours.

　　3. Spoon the mixture into the bottle and then add another 250ml / 1 cup water. Put the lid on (tightly!) and shake the mixture.

　　4. Leave the bottle to rest until there are no visible air bubbles. This usually takes at least 12 hours. After this, the mixture will be clear, and be noticeably more viscous than water.

　　5. Clean the board and the paintbrush thoroughly to remove any dust or dirt that you don't want in the paper.

　　6. Pour about 60ml / ¼ cup of the MC solution on the board. Use the paintbrush to spread the mixture evenly across the board, covering an area larger than the tissue paper you will be using. Add more MC solution if necessary.

　　7. Roll one sheet of tissue paper around the cylinder, avoiding any wrinkles. This will be the first sheet, and will be wetter than the second sheet. This means the colour is more likely to bleed out of this sheet, so if you are using two different colours, you should use the lighter coloured sheet here.

　　8. Unroll the tissue paper onto the board so that it doesn't have any wrinkles. Use the paintbrush to brush any air bubbles to the sides out from under the tissue paper, so that it lies completely flat. Do this carefully because the wet tissue will tear easily – a wide paintbrush prevents too much pressure in any one spot.

　　9. Roll the second sheet of tissue paper around the cylinder, again avoiding any wrinkles.

　　10. Unroll the second sheet of tissue paper onto the board so that it overlaps with the first sheet. There should be enough liquid that there are no dry patches. If there are dry patches, carefully brush a small amount of the MC solution over these regions. As before, use the paintbrush to brush any air bubbles to the sides out from under the tissue paper, so that it lies completely flat.

　　11. Leave the paper to dry fully. This could take more than 24 hours. It is important not to peel off part of the paper while it is wet, because the peeled region will become stretched relative to the rest of the paper even when it dries.

　　12. When the paper has dried, peel it carefully off the board, and cut it to size (see page 9).

欢迎转载双层纸怎么制作，双色纸制作方法，请注明出处：跟我学做纸艺花